Offer Description:
Materials and Dimensions
1. Container Material: Heat resistant (borosilicate) glass
2. Capacity / Fill Line: 240 milliliters
3. Heater Housing / Handle: White Plastic
4. Base Housing: White Plastic
5. Cord: White
6. Spout tip: Rounded, fits well in any nostril (? ? )
7. Height of spout tip: Far enough above fill line to prevent boiling through spout.
Design Details
--------------
- Heater housing and handle are integrated to appear as one part.
- Edge around bottom of heater housing is rounded, flush with outer edge of handle.
- Kettle shape is revolved parabola.
Operation
1. Plug in: )
2. Fill container with water to line. Add salt if desired.
3. Depress Switch (starts boiling cycle)
4. Wait for LED to turn Green, along with audible "beep beep beep" from speaker.
5. Use normally as Neti Pot.
Operating Requirements
1. When switch depressed, LED lights RED.
2. Must boil water within 90 seconds (faster is better)
3. Must maintain boiling for 60 seconds.
4. Water must not boil over top of container!
5. After boiling, turn off heater; LED blinks RED slowly.
6. When water cools to 38 degrees Celsius; LED lights GREEN, speaker makes "beep beep beep. "
7. When container removed from base, system shuts off.
8. When outlet is exposed to salt water, must not short-circuit. i. e., base/outlet must have circuit breaker.
Failure Modes
1. Container is dry -- Auto Shutoff when temperature exceeds 120 degrees.
2. Boiling takes too long -- Auto Shutoff when boil not reached after 3 minutes.
3. Water never used -- Auto Shutoff after 30 minutes.
1. Container Material: Heat resistant (borosilicate) glass
2. Capacity / Fill Line: 240 milliliters
3. Heater Housing / Handle: White Plastic
4. Base Housing: White Plastic
5. Cord: White
6. Spout tip: Rounded, fits well in any nostril (? ? )
7. Height of spout tip: Far enough above fill line to prevent boiling through spout.
Design Details
--------------
- Heater housing and handle are integrated to appear as one part.
- Edge around bottom of heater housing is rounded, flush with outer edge of handle.
- Kettle shape is revolved parabola.
Operation
1. Plug in: )
2. Fill container with water to line. Add salt if desired.
3. Depress Switch (starts boiling cycle)
4. Wait for LED to turn Green, along with audible "beep beep beep" from speaker.
5. Use normally as Neti Pot.
Operating Requirements
1. When switch depressed, LED lights RED.
2. Must boil water within 90 seconds (faster is better)
3. Must maintain boiling for 60 seconds.
4. Water must not boil over top of container!
5. After boiling, turn off heater; LED blinks RED slowly.
6. When water cools to 38 degrees Celsius; LED lights GREEN, speaker makes "beep beep beep. "
7. When container removed from base, system shuts off.
8. When outlet is exposed to salt water, must not short-circuit. i. e., base/outlet must have circuit breaker.
Failure Modes
1. Container is dry -- Auto Shutoff when temperature exceeds 120 degrees.
2. Boiling takes too long -- Auto Shutoff when boil not reached after 3 minutes.
3. Water never used -- Auto Shutoff after 30 minutes.
| Category | Health & Medicine |
| Posting Date | 2019-03-19 |
| Contact_Person | Mr. Tom Ghali |
| Company | Aquattix |
| Address | 11740 Dublin Blvd, Ste 100, Dublin, Ca, United States |
| Country | United States |
No comments:
Post a Comment
Thank you for submitting your comments; every comment is approved manually and may take up to few days, if you consider any mistake, let us know.